MANUAL.

Bh vw-c2 ml/en: Unterschied zwischen den Versionen

← Zum vorherigen Versionsunterschied
VisuellWikitext
FuzzyBot (Diskussion | Beiträge)
268 Bearbeitungen
Übernehme Bearbeitung einer neuen Version der Quellseite
FuzzyBot (Diskussion | Beiträge)
268 Bearbeitungen
Übernehme Bearbeitung einer neuen Version der Quellseite
 
(4 dazwischenliegende Versionen von einem anderen Benutzer werden nicht angezeigt)
Zeile 1: Zeile 1:
{{:bh_ml_begin}}
{{:bh_ml_begin}}


<span id="1._Handyhalterung"></span>
==1. {{#lst:bh_m_heading|phoneholder}}==
== 1. cell phone holder ==


<div style="display: flex; flex-wrap: wrap; gap: 50px; justify-content: center;">
{{:StepFlex | content=
  {{:StepBox|img=bh_vw-c2_sl_pic-000.png|line=ml|number=1|key=prepare_gluing}}
  {{:StepBox|img=bh_vw-c2_ml_pic-001.png|line=ml|number=2|key=remove_protective_film}}
  {{:StepBox|img=bh_vw-c2_ml_pic-002.png|line=ml|number=3|key=insert_cable}}
  {{:StepBox|img=bh_vw-c2_ml_pic-003.png|line=ml|number=4|key=holder_mount}}
}}


<div style="display: inline-block; text-align: center; max-width: 360px; word-wrap: break-word; white-space: normal;">
==2. {{#lst:bh_m_heading|cablerouting}}==
{{#invoke:BoxModul|fotobox|bh_vw-c2_sl_pic-000.png|360}}
<div>
'''1. prepare bonding'''
</div>
* Clean the adhesive surface with an alcohol wipe and test the adhesive effect using the enclosed TEST adhesive. If it does not hold, clean further, see our [[Special:MyLanguage/Bh caq|Q&A]].
</div>
 
<div style="display: inline-block; text-align: center; max-width: 360px; word-wrap: break-word; white-space: normal;">
{{#invoke:BoxModul|fotobox|bh_vw-c2_ml_pic-001.png|360}}
<div>
'''2. remove protective film'''
</div>
* Now remove the red protective film from the adhesive on the holder.
</div>
 
<div style="display: inline-block; text-align: center; max-width: 360px; word-wrap: break-word; white-space: normal;">
{{#invoke:BoxModul|fotobox|bh_vw-c2_ml_pic-002.png|360}}
<div>
<div lang="de" dir="ltr" class="mw-content-ltr">
'''3. Kabel einsetzen'''
</div>
</div>
<div lang="de" dir="ltr" class="mw-content-ltr">
* Setze das Ladekabel entsprechend der Abbildung in die Halterung ein.
</div>
</div>
 
<div style="display: inline-block; text-align: center; max-width: 360px; word-wrap: break-word; white-space: normal;">
{{#invoke:BoxModul|fotobox|bh_vw-c2_ml_pic-003.png|360}}
<div>
<div class="mw-translate-fuzzy">
'''3. mount the holder'''
</div>
</div>
* Position the holder as shown in the illustration and secure it by applying pressure.
</div>
 
</div>
 
 
 
<span id="2._Kabelführung"></span>
== 2. cable routing ==


{{:bh_vw-c2_cr}}
{{:bh_vw-c2_cr}}


{{:bh_ml_end}}
{{:bh_ml_end}}

Aktuelle Version vom 10. August 2025, 10:08 Uhr

INSTRUCTIONS.

The following are the essential steps for installing your new phone holder. We will start with installing the holder itself and then use our cable management kit to give your cockpit a clean look.

1. Mobile phone holder

1. Prepare gluing

  • Clean the adhesive surface with an alcohol wipe and test the adhesive effect using the enclosed TEST adhesive. If it does not hold, clean further, see our Q&A.

2. Remove protective film

  • Now remove the red protective film from the adhesive on the holder.

3. Insert cable

  • Insert the charging cable into the holder as shown in the illustration.

4. Mount holder

  • Position the holder as shown in the illustration and secure it by applying pressure.

2. Cable routing

1. prepare bonding

  • Clean the adhesive area with the cleaning cloth, wait one minute before continuing.

2. cable in position

  • Place the cable in the position shown in the illustration and plug it into the USB socket.

3. prepare bonding

  • Remove the red protective film from the adhesive tape on the cable guide.

4. gluing

  • Install the cable guide at the marked position.

Notes

Frequently asked questions can be found in my Q&A, for all other questions please contact us by email info@beevention.com.

Abgerufen von „https://manual.beev.info/index.php?title=Bh_vw-c2_ml/en&oldid=871“